So the AFS light on your 2005-2012 Acura RL is blinking and the headlights quit swiveling or leveling. That means the adaptive front lighting system has dropped into fail-safe mode because it sees a fault in one of its inputs. One of those inputs is the headlight leveling sensor at the left rear of the car, and the good news is the Acura manual gives a simple bench test for it. I’ve been turning wrenches since my ’87 Subaru, and this is about as friendly as a diagnosis gets. Here’s the plan: read the AFS trouble codes, test the sensor with an ohmmeter against the Acura specification, replace it if it fails, and then run the Acura learning procedure for the leveling sensor.
Quick answer
Symptom: AFS indicator blinking in the gauge, headlights no longer swivel with the steering or self-level.
What the blink means: Acura says the system has entered fail-safe mode after a fault in a sensor, the B-CAN line, or the control unit.
Sensor test: terminals 1 and 3 should read about 3.5 to 6.5 kilohms; terminals 2 and 3 should read about 0.5 to 4.5 kilohms with the linkage moved.
Part: Acura 33146-SJA-003, the rear headlight level sensor listed for the 2005-2012 RL.
After replacement: Acura requires the adaptive front lighting control unit learning procedure, which uses the HDS scan tool.
What the blinking AFS light means
First, a quick look at what you’re dealing with. The Acura RL’s adaptive front lighting system, or AFS, does two jobs. It swivels the headlight beams left and right as you steer, and it levels the beams up and down as the car’s body pitches with load. According to the Acura service manual for the RL, the system consists of the adaptive front lighting control unit, the headlight leveling sensor, the steering angle sensor, the headlight leveling motors, the adaptive front lighting gearbox, the AFS indicator in the gauge, and the adaptive front lighting OFF switch.
The manual is direct about what the blinking light means. If a malfunction occurs in any of the sensors, the B-CAN line, or the control unit, the system moves to fail-safe mode. It stops control, and the AFS indicator blinks to show the malfunction. If the swivel control has the fault, the headlight aiming stays centered. If the leveling control has the fault, the headlight aiming stays at 0.6 degrees under the present position.
So a blinking AFS light isn’t a bulb problem and not a simple switch setting. It’s the control unit telling you it has stored a fault and shut itself down. The headlights still work as ordinary headlights, but they no longer follow the road or adjust for load.
How the leveling side of the system works
It helps to know how the pieces talk to each other. Acura describes the two control paths separately. Horizontal movement, the swivel, comes from the steering angle sensor and the vehicle speed pulse, sent through the control unit to the adaptive front lighting gearboxes. Swivel control only starts when the headlight switch is on, the AFS switch is on, and the car is moving faster than 5 mph (8 km/h).
Vertical movement, the leveling, comes from the headlight leveling sensor. The sensor sends signals about vertical movement through the control unit to the headlight leveling motors. Leveling control starts when both the ignition switch and the headlight switch are on. The Acura component location index lists the headlight leveling sensor under the left rear of the vehicle, which on a US car is the driver side rear.
The sensor test in the manual tells you what kind of part this is. Acura specifies a fixed resistance across one pair of terminals and a resistance that changes as the linkage moves across another pair. In other words, the sensor’s output changes with linkage position, and the control unit uses that signal to drive the leveling motors.
Acura also describes a start up routine you can watch for. When the headlight switch is on, the swivel angle is initialized every time: the right headlight aiming moves right 22.2 degrees and the left headlight aiming moves right 0.8 degrees, then both return to center. Seeing that sweep tells you the swivel motors and gearboxes are at least responding.
Read the trouble codes first
Don’t start throwing parts at it yet. The AFS control unit has its own self diagnostic function, so the first step’s getting the codes out. Acura’s preferred tool is the HDS, the Honda Diagnostic System. With the HDS you can select the AFS system, read codes, view the data list, and run a function test that forces the headlights to swing and move up and down.
The manual also gives a method for displaying the codes with the AFS indicator, marked for use only if the HDS is unavailable:
- Turn the ignition switch OFF.
- Short the SCS line to body ground.
- Turn the ignition switch ON (II). The AFS indicator comes on for 2 seconds.
- Within 3 seconds after the indicator turns off, push the AFS OFF switch three times.
- Within 6 seconds after the indicator turns off, the indicator starts to show the codes. If there’s a code, the indicator blinks. If there are no codes, the indicator comes on and stays on.
Acura also notes that before troubleshooting the AFS, you should troubleshoot the multiplex integrated control system first using B-CAN System Diagnosis Test mode A, because the AFS relies on the B-CAN network and a network fault can look like an AFS fault.
To erase codes without the HDS, the manual gives this sequence: ignition off, short the SCS line to body ground, ignition on (the indicator comes on for 2 seconds and initializes for 1.5 seconds), then within 3 seconds after the indicator turns off push and hold the AFS switch, release it within 3 seconds after the indicator comes on, and push it once more within 3 seconds after the indicator turns off. The indicator should blink twice. If it doesn’t, repeat from the first step.
Testing the headlight leveling sensor
This is the fun part, and you won’t need anything fancier than a basic ohmmeter. The Acura procedure for testing the sensor is short. Here it is as the manual gives it:
- Remove the headlight leveling sensor.
- Measure resistance between leveling sensor 3P connector terminals No. 1 and No. 3. There should be about 3.5 to 6.5 kilohms.
- Measure resistance between leveling sensor 3P connector terminals No. 2 and No. 3 with the linkage moved. There should be about 0.5 to 4.5 kilohms.
- If the resistance isn’t as specified, replace the leveling sensor.
- After replacement, do the adaptive front lighting control unit learning procedure.
| Test | Terminals | Acura specification |
|---|---|---|
| Fixed resistance | No. 1 and No. 3 | About 3.5 to 6.5 kilohms |
| Moving resistance | No. 2 and No. 3, linkage moved | About 0.5 to 4.5 kilohms |
Two practical notes follow from that test. First, on the second check, move the linkage slowly through its travel and watch the meter. The specification is a range, and the reading should stay within it as the linkage moves. Second, because the sensor lives under the car near the rear suspension, look at the 3P connector and its terminals while it’s apart. The manual’s control unit input test tells you to inspect connector and socket terminals for bent, loose, or corroded terminals and repair them as necessary. That same care applies at the sensor end.
If you need a refresher on meter setup and good lead contact, our guide on testing grounds with a multimeter covers the basics. A kilohm range check like this one is one of the simpler measurements you can make.
If the sensor tests good
Sensor checked out fine? Then it’s time to look elsewhere. A sensor that meets both specifications points you back toward the wiring and the control unit. Acura’s Control Unit Input Test for the AFS starts with removing the driver’s dashboard lower cover and disconnecting the 40P connector from the adaptive front lighting control unit. You then inspect the connector and socket terminals for good contact, run the input tests at the connector with it disconnected, and then reconnect it and run the tests again. If any test shows a problem, Acura says to find and correct the cause, then recheck the system. If all input tests prove OK, the manual concludes the control unit must be faulty and should be replaced.
Replacing a control unit brings its own learning procedure, and it’s a far more expensive step than a sensor. That’s the reason to follow the order in the manual. Prove the network with B-CAN Test mode A, prove the sensor against its resistance specification, prove the wiring, and only then condemn the control unit.
Headlight leveling sensor replacement, per the Acura manual
If the sensor failed, the swap itself isn’t a big job. The Acura procedure for replacing the headlight leveling sensor on the RL is brief. The sensor is under the left rear of the vehicle.
- Lift the vehicle and support it with safety stands.
- Disconnect the 3P connector from the headlight leveling sensor.
- Remove the bolts and nut, then remove the headlight leveling sensor.
- Install in the reverse order of removal.
- After replacement, do the adaptive front lighting control unit learning procedure.
The manual excerpt for this procedure doesn’t list a torque value for the sensor fasteners, so none is given here. Obtain the correct fastener specifications and illustration for the exact vehicle before reassembly rather than guessing a torque. Route the harness the way the original was routed so it stays clear of moving suspension parts.
Do not skip the learning step
Acura lists the learning procedure as the last step of both the sensor test and the sensor replacement. The control unit needs to learn the new sensor’s position before leveling works correctly.
The learning procedure after a leveling sensor replacement
Don’t skip this step, because this is the part that trips people up. Acura’s manual gives a separate learning procedure for when the headlight leveling sensor is removed or replaced, or the leveling sensor link is disassembled. It requires the HDS. The manual notes that if the AFS indicator is blinking, check the DTCs first.
- Remove all of the baggage from the vehicle.
- Connect the HDS to the data link connector, and short the SCS line.
- Turn the ignition switch ON (II).
- Make sure the AFS indicator turns off after 2 seconds. If it stays on and doesn’t turn off, the AFS control unit has been replaced with a brand new control unit, which uses a different learning procedure.
- Turn the ignition switch OFF and then back ON (II).
- Within 5 seconds, turn the headlight switch ON/OFF or to passing three times.
- Turn the headlights ON, and make sure the headlights move up and down. If they don’t move, return to step 2.
- Release the SCS short command with the HDS.
- Adjust the headlights.
Acura puts the baggage removal first for a reason: the leveling sensor responds to vertical movement at the rear, so learning should happen with the car unloaded. The final step, adjusting the headlights, points to the headlight adjustment procedure in the same manual, so the beams are aimed correctly once leveling is working again.
If you’re replacing the AFS control unit itself, Acura gives two other learning procedures, one for a brand new unit and one for a known good used unit. Both add steps for steering center learning: turning the steering wheel 90 degrees or more from center to the left and right, then test driving, with only the driver in the car, in a straight line for 98.4 feet (30 m) at 16 mph (25 km/h) or more. Those steps are for the control unit, not for a leveling sensor replacement.
Acura part number and price
Now for the part you’ll actually order. The Acura parts catalog lists the rear headlight level sensor for the RL as 33146-SJA-003. On HondaAcuraOnline the listing shows it for the 2005-2012 Acura RL, describes it as a headlamp adjuster, and gives the other names Sensor and Sensor Assembly Rear. Honda’s own parts naming on the Amayama catalog calls it Sensor Assy., Headlight Adjuster Rr.
| Item | Acura number | Listed fitment | Price checked Nov 4, 2026 MT |
|---|---|---|---|
| Headlight level sensor (rear) | 33146-SJA-003 | 2005-2012 Acura RL | HondaAcuraOnline: MSRP $1,071.74, sale price $720.22 |
Prices for this part vary widely between dealers and can change at any time, so check the current price and confirm fitment by VIN with the seller before you order. We aren’t listing aftermarket alternatives, used part pricing, or repair workarounds here, because none of them could be checked against an Acura source for this article.
Common mistakes
- Guessing at the part. A blinking AFS light can come from the leveling sensor, the steering angle sensor, the B-CAN network, the motors, the gearboxes, or the control unit. Read the codes first.
- Skipping the network check. Acura says to run B-CAN System Diagnosis Test mode A before troubleshooting the AFS.
- Testing the linkage in one spot. The second resistance check is made with the linkage moved, so move it through its travel.
- Ignoring the connector. Inspect the 3P connector and terminals for corrosion and poor fit while the sensor is out.
- Learning with a loaded trunk. The learning procedure starts with removing all baggage.
- Forgetting to aim the headlights. Every learning procedure ends with adjusting the headlights.
For more electrical and body fixes on Honda and Acura models, see our guides to the Acura MDX liftgate wiring problem and the Honda Odyssey SRS light and seat belt buckle switch, or browse the car maintenance hub.
Before crawling under the RL: establish what actually stopped working
I would write down whether the AFS indicator is blinking, whether either headlamp is dark, and whether the complaint is low beam aim, missing swivel, or both. Those descriptions are not interchangeable. A lighting fault that makes a lamp go out still needs its own diagnosis; a leveling sensor replacement is not a cure for every headlight complaint on an RL.
Do not judge the swivel solely by turning the steering wheel in the driveway. The operating conditions described above include vehicle speed, so a stationary observation can be misleading. Use the factory function test where appropriate rather than inventing a moving nighttime test while watching the lamps instead of the road. Keep other people clear of the vehicle during commanded movement.
Record recent work too. Has the sensor link been disturbed, has the rear suspension been repaired, or was the control unit replaced? The learning instructions distinguish these situations. Knowing what was touched can explain why a physically intact component now needs the correct setup procedure, without proving that a different replacement part is required.
Get the tools ready before removing a sensor you cannot finish calibrating
The bench measurement is simple; completing the entire job needs more than an ohmmeter. Plan for safe lifting equipment, suitable hand tools, correct terminal adapters, the service illustrations, and access to the HDS functions required for learning. I would arrange the calibration before dismantling if my own tool cannot perform it. “Reads engine codes” is not the same capability as communicating with AFS and commanding its service functions.
Print or save the Acura leveling-sensor test and illustration. The illustration identifies the actual part and connector. Match the terminal numbering to the connector view rather than assuming left-to-right numbering from whichever side happens to face you. Photograph the original linkage and harness routing before disturbing them.
Use the specified lifting and support points on a suitable surface, secure the car against movement, and never work underneath a vehicle supported by a jack alone. If rusty hardware or an awkward access angle prevents a controlled removal, stop before breaking the bracket or stressing the harness. A damaged mounting arrangement can turn a straightforward sensor job into a mechanical repair that learning cannot correct.
How to make the resistance check useful rather than misleading
Test the removed sensor as Acura directs, not a powered vehicle circuit. Start by checking that the meter and leads behave normally and that the display is on the appropriate resistance range. Kilohms and ohms are different units: a value displayed in kilohms must not be compared as if it were an unscaled ohm reading.
Keep the probes stable while moving the linkage through its intended motion. Do not force it beyond its mechanical travel. If the display jumps, first establish whether a lead slipped or contact at a terminal changed. Repeat a questionable measurement with sound contact before buying a costly component. Save the readings from both specified terminal pairs so the conclusion can be checked later.
A sensor that fails the manufacturer’s limits supports replacement. A sensor that passes does not by itself certify the installed harness, connector, network or control unit. Reconnect the diagnostic reasoning to the actual AFS code and the appropriate factory input tests. Avoid the tempting leap from “sensor good” straight to “module bad,” especially if corrosion or poor terminal contact has not yet been addressed.
For circuit testing, follow each diagram’s connected or disconnected state and ignition instruction. Never apply an ohmmeter to an energized circuit or insert oversized probes into terminals. Do not improvise an SCS short at an unidentified connector. Use the proper service method and tools; an accidental bridge to a power circuit is not a harmless substitute for a diagnostic command.
Separate mechanical installation, learning and beam aim
These are three deliverables. Installation puts a correctly mounted sensor and linkage back on the vehicle with the connector secure and wiring protected. Learning establishes the control unit’s reference according to the applicable procedure. Headlamp adjustment then establishes correct beam aim. Checking one box does not silently complete the others.
That distinction helps if the warning disappears but the lamps still look wrong. Do not compensate for an unresolved learning problem by winding the mechanical adjusters until the beam seems acceptable against a nearby wall. Follow the complete sequence and the specified aiming setup. Incorrect aim can reduce the driver’s view or glare into oncoming traffic even when the indicator is no longer blinking.
The source procedure here is the 2006 RL manual. For another year within the parts listing, confirm the service instructions and connector details for that exact car. A shared catalog fitment is evidence about a part application, not proof that every diagnostic instruction and software step remained unchanged throughout the model run.
What a complete estimate and handover should include
Ask for diagnosis, the confirmed part and fitment, any damaged linkage or connector repair, learning, and headlamp adjustment as distinct line items. The sensor price shown earlier is a dated dealer listing, not a current quote or a prediction of the installed bill. Labor rates, hardware condition and additional proven faults change the total.
Before authorizing a control unit, ask which input tests failed or passed and whether the network check was completed. For a replacement sensor, retain the failed resistance results if available. At collection, request confirmation that the correct learning branch was completed, the AFS codes were rechecked and the beams were adjusted. That is a useful completion record, not just a receipt saying the blinking lamp was cleared.
If the warning returns, bring that record and describe exactly when it returned. A fault immediately after setup and an intermittent warning after wet-weather driving are different observations, not proof of different parts by themselves. Good notes let the next diagnostic pass start with evidence instead of repeating the same sensor guess.
Check the replacement before committing to installation
Compare the supplied component with the removed sensor while both are on the bench: connector, mounting arrangement, linkage and any included bracket. Resolve a mismatch with the seller using the VIN and full part number before forcing it into place. Keep packaging and verify the return terms before installation, particularly for electrical parts. A part described only as “fits Acura AFS” is not enough identification for this repair. If a bracket or link must be reused, confirm that it is serviceable and that the assembly follows the factory arrangement rather than copying an improvised previous repair.
FAQ
Why is the AFS light flashing on my Acura RL?
Acura says the AFS indicator blinks when the system enters fail-safe mode after a malfunction in a sensor, the B-CAN line, or the control unit. Read the AFS codes to find which one.
Where is the AFS leveling sensor on an Acura RL?
The Acura component location index lists the headlight leveling sensor under the left rear of the vehicle, the driver side rear on a US car.
How do you test an Acura RL headlight leveling sensor?
Remove it and measure resistance at its 3P connector. Terminals 1 and 3 should read about 3.5 to 6.5 kilohms. Terminals 2 and 3 should read about 0.5 to 4.5 kilohms with the linkage moved.
Do I need to recalibrate after replacing the leveling sensor?
Yes. Acura requires the adaptive front lighting control unit learning procedure after the sensor is removed or replaced, and that procedure uses the HDS.
Can I still drive with the AFS light flashing?
The headlights still work, but swivel and leveling stop. If leveling has failed, Acura says the aim stays 0.6 degrees under its present position, so the beam may look shorter. Get it diagnosed.
What is the Acura part number for the RL rear leveling sensor?
33146-SJA-003, listed for the 2005-2012 RL. Confirm fitment by VIN with the seller.
Sources: Acura 2006 RL service manual sections for the AFS system description, AFS on-board diagnostics, Headlight Leveling Sensor Test and Replacement, Control Unit Input Test, and Adaptive Front Lighting Control Unit Learning Procedure (via charm.li); HondaAcuraOnline and Amayama catalog listings for 33146-SJA-003.
Note To Reader: Car Nut Chronicles is reader supported. We may post content which contains links to affiliate sites such as Amazon where we may earn a small commission. This helps us keep the lights on and the articles you enjoy being produced. Thank you for your readership, we appreciate you!

2005-2012 Acura RL AFS Light Flashing: Replace Rear Leveling Sensor
Acura RL AFS light blinking? Test the rear headlight leveling sensor against the Acura spec, replace it if it fails,…
How to Defog a Windshield Fast: The Settings That Clear It Quickest
Fog on the inside of your windshield? Use Defrost, max heat, A/C on and fresh air. Here is why it…
2004 Lincoln LS ABS and Traction Light: Rear Wheel Speed Sensor Fix
Fix the ABS and traction lights on a 2004 Lincoln LS: read codes C1165, C1175, C1235 or C1236, run the…
The Pontiac Grand Am… 400? A Rare Gem For Sure.
400-Powered 1978 Pontiac Grand Am Recently Listed For $14,500 Before Fees The Pontiac Grand Am, a dynamic presence in GM’s lineup during the seventies and early eighties, had its share of ups and downs in terms of sales, and 1978 was no exception to that. However, its trajectory took a…
Chevy 6-Lug Bolt Pattern by Year: 6×5.5 (6×139.7) Chart for Silverado, Tahoe, Colorado and More
Chevy half-tons since 1999 use 6×5.5 (6×139.7). Year-by-year chart with 78.1 mm bore, M14x1.5 studs, 140 lb-ft torque, and which Toyota and Ram wheels fit.
Spider Silk Supercar Is A Thrilling Challenge
Revolutionary Supercar Crafted from Spider Silk Promises Unprecedented Strength and Lightness A groundbreaking endeavor in the automotive world is underway as a US company Velozzi explores the possibility of creating a spider silk Supercar. A material proven to be five times stronger than steel when thousands of nano strands form…
How to Keep Mice Out of a Car Engine in Storage: What Actually Works
Keep mice out of a stored car engine: remove food, seal quarter inch gaps and set snap traps. What research says on peppermint, ultrasonic and soy wiring.
Lexus LS430 Locks, Windows and Smart Key Dead? Unplug the Rain Sensor
LS430 locks, smart key, mirrors and window switches all dead with a good battery and fuses? Unplug the rain sensor behind the mirror. Here is how and what next.
2023 LA Auto Show: Time To Energize and Be Authentic
The 2023 LA Auto Show offered enthusiasts a glimpse into the future of driving along with street food excellence. Featuring test drives and electrifying vehicle innovations, the event also hosted the USA Street Food Awards. A first-hand showcase of cutting-edge technology, it also provided visitors with culinary delights such as…

