If your 2004 Lincoln LS just lit up the ABS and traction control lights together, there’s a good chance you’re looking at a failed rear wheel speed sensor or a wiring fault behind it. I’m a Buick guy at heart, so I’ve got a soft spot for big comfy cruisers, and the LS deserves a proper fix, not a guess. Here’s the plan: read the codes stored in the ABS module, follow the Ford pinpoint test for that code to prove whether the sensor, the harness, or the module is at fault, and then replace the rear sensor, which is held in by one bolt torqued to 9 Nm (80 lb-in).
Quick answer
Symptom: ABS and traction control lamps on, often with no change in how the brakes feel during normal stops.
Most likely codes: C1165 (RR) or C1175 (LR) for an input circuit failure, and C1235 (RR) or C1236 (LR) for a missing signal.
Test: Ford Pinpoint Test E for circuit failures and Pinpoint Test F for missing signal codes. Both are laid out below.
Fix: Replace the rear wheel speed sensor. One bolt, 9 Nm (80 lb-in). The sensor ring isn’t sold separately; Ford says it’s serviced with the rear halfshaft.
Ford part numbers: 3W4Z-2C190-AA (driver side rear) and 3W4Z-2C190-BA (passenger side rear), both now listed as discontinued by Ford.
What the warning lamps are telling you
The Lincoln LS uses one ABS module to run the anti-lock brakes and the traction control. That module watches all four wheel speed sensors at once. According to the Ford workshop manual, the ABS module compares the wheel speed inputs from all four sensors to decide when a wheel is about to lock. If one of those four inputs goes missing, or the circuit behind it reads wrong, the module can’t trust its math anymore. It stores a code, turns on the ABS warning lamp, and shuts down the functions that depend on wheel speed, which includes traction control. That’s why the two lamps tend to come on together. This is the part that trips people up, so don’t go hunting for two problems.
This matters for how you approach the repair. Two lamps on at once doesn’t mean two separate failures. In most cases one input to one module has dropped out, and every system that shares that input reacts. Start with the ABS module codes and let them tell you which corner of the car to look at.
When the ABS lamp is on, the anti-lock function is disabled. Ordinary braking still works through the hydraulic system, but the wheels can lock in a hard stop on a slick road. Treat the lamp as a reason to fix the car soon, not as something to live with. If you are also chasing a soft pedal or a pedal that sinks, that is a separate hydraulic problem, and our guide on diagnosing a soft, spongy brake pedal walks through that side of things.
How the LS wheel speed sensors work
Here’s the thing to understand before you grab a meter: the 2004 LS uses active wheel speed sensors, not the older passive magnetic pickups found on many earlier cars. The Ford manual describes it plainly: the active wheel speed sensor generates a square wave signal that’s sent to the ABS module. Twelve volts are supplied to the active sensors from the ABS module, and the sensor ground is also supplied by the ABS module. Each sensor connects to ABS module connector C135 through two wires and a connector at the wheel.
The manual also notes that when the ignition is turned to RUN, the ABS module runs a self test by sending a reference voltage through the sensor circuits to see if they are functional. Ford splits the faults into two groups of codes: circuit failures, and signal missing codes that relate to the signal the module sees from a turning wheel.
The active design changes how you should test. A passive sensor is basically a coil, so many people check it with an ohmmeter and look for a resistance value. An active sensor has electronics inside, and Ford doesn’t give a resistance specification for the sensor itself. Instead, the factory tests check the wiring for shorts and opens, check for shorted sensor circuits, and then check the voltage the ABS module supplies. Do not condemn or clear a sensor based on a quick ohms reading across its pins alone.
Codes that point to a rear wheel speed sensor
Let’s talk codes. The Ford ABS module DTC index for the 2004 LS lists eight wheel speed codes. Four are circuit failures that send you to Pinpoint Test E, and four are missing signal codes that send you to Pinpoint Test F. The rear wheel codes are the ones that matter for this repair, but the full list helps you read a scan tool report correctly.
| DTC | Description (Ford wording) | Ford test |
|---|---|---|
| C1145 | Wheel Speed Sensor RF Input Circuit Failure | Pinpoint Test E |
| C1155 | Wheel Speed Sensor LF Input Circuit Failure | Pinpoint Test E |
| C1165 | Wheel Speed Sensor RR Input Circuit Failure | Pinpoint Test E |
| C1175 | Wheel Speed Sensor LR Input Circuit Failure | Pinpoint Test E |
| C1233 | Wheel Speed LF Input Signal Missing | Pinpoint Test F |
| C1234 | Wheel Speed RF Input Signal Missing | Pinpoint Test F |
| C1235 | Wheel Speed RR Input Signal Missing | Pinpoint Test F |
| C1236 | Wheel Speed LR Input Signal Missing | Pinpoint Test F |
Note the order of the letters in those codes. On the circuit failure codes, C1165 is right rear and C1175 is left rear. On the missing signal codes, C1235 is right rear and C1236 is left rear. Ford also uses LR for left rear and RR for right rear, which on a US car means LR is the driver side and RR is the passenger side. Getting the side right before you order a sensor saves a second trip under the car.
You need a scan tool that can read the ABS module, not just the engine computer. A basic code reader that only talks to the powertrain module will often show nothing at all while the ABS lamp is on. The Ford manual also says to always retrieve the continuous DTCs after running the self test, so read both the on demand results and the stored codes.
Pinpoint Test E: rear sensor circuit failure (C1165 or C1175)
If you’ve got a circuit failure code, Pinpoint Test E is where you’ll spend your time. It covers the input circuit failure codes. Ford lists the possible causes as the wheel speed sensor, the wheel speed sensor harness circuits (power or ground), and the ABS or wheel speed sensor connectors. The manual carries a caution to use the Flex Probe Kit for all test connections and not standard multimeter probes, to prevent damage to the wiring terminals.
The test checks both circuits for the suspect wheel. These are the rear circuits at ABS module connector C135, as listed in the manual:
| Wheel | Circuit | Wire color | C135 pin | Sensor connector pin |
|---|---|---|---|---|
| Right rear | 7-CF40 | YE/GN | 43 | 1 |
| Right rear | 8-CF40 | WH/GN | 42 | 2 |
| Left rear | 7-CF34 | YE/BU | 36 | 1 |
| Left rear | 8-CF34 | WH/BU | 37 | 2 |
Here’s how the Ford test steps run, in the order given in the manual:
- E1, check for a short to power. Key off. Disconnect ABS module connector C135 and the suspect wheel speed sensor. Key on. Measure voltage between the C135 pins for that wheel, harness side, and ground. Both circuits must be checked. If voltage is present, repair the circuit, clear the codes, and repeat the self test. If not, go to E2.
- E2, check for a short to ground. Key off. Measure resistance between the same C135 pins, harness side, and ground. If the resistance is greater than 10,000 ohms, go to E3. If not, repair the circuit.
- E3, check for an open. Measure resistance between each C135 pin and its matching pin at the sensor connector, harness side. If both read less than 5 ohms, go to E4. If not, repair the circuit.
- E4, check for shorted sensor circuits. Measure resistance between the two pins of the suspect wheel speed sensor. If the resistance is greater than 10,000 ohms, go to E5. If not, repair the circuit in question.
- E5, check the ABS module output. Reconnect C135. Key on. Measure the voltage between the two sensor pins on the harness side. The manual’s question is whether the voltage is less than 9 volts. A yes answer sends you to install a new ABS module. A no answer sends you to install a new wheel speed sensor. In both cases, clear the code and repeat the self test.
The logic is worth understanding. Steps E1 through E3 prove the two wires between the module and the wheel aren’t shorted to power, not shorted to ground, and not broken. Step E4 makes sure the circuits aren’t shorted to each other. Step E5 proves the module is sending proper supply voltage to the sensor. If the wiring is good and the module is supplying voltage, the sensor is the part left, the test result, not the lamps alone, is what supports that replacement.
If you are new to resistance and voltage drop checks with a meter, our walkthrough on testing grounds with a multimeter covers meter setup and lead placement. The car is different, but the meter habits carry over.
Pinpoint Test F: rear sensor signal missing (C1235 or C1236)
Got a signal missing code instead? Then Pinpoint Test F is your roadmap. Here the circuit is intact enough to pass the module self test, but the module isn’t getting a believable signal from the wheel. Ford lists the possible causes as mismatched tire sizes, the wheel speed sensor ring, the wheel speed sensor, and the ABS module. The steps in the manual are:
- F1, check for DTCs. Key on, connect the diagnostic tool. If C1145, C1155, C1165, or C1175 is present, go to Pinpoint Test E first.
- F2, check the wheel speed PIDs. Watch all four wheel speed PIDs on the scan tool while driving at a constant speed. If the four values are similar, clear the code and drive the car. If C1233, C1234, C1235, or C1236 comes back, Ford says to install a new ABS module. If the four values aren’t similar, go to F3.
- F3, check the sensor for damage or looseness. Key off, raise and support the car. Ford cautions you to examine the sensor wire carefully with a good light, because missing damage in the wire can lead to replacing a good part. Inspect the sensor mounting for looseness and inspect the sensor and its mounting surface for corrosion, cleaning as needed. If the sensor isn’t OK, install a new sensor.
- F4, check for sensor ring damage. Remove the sensor, then inspect the sensor ring for damaged or missing teeth, rotating the wheel to check all of it. If the ring is OK, go to F5.
- F5, check the ABS module output. Key on, measure the voltage between the ABS module C135 pins and the suspect sensor connector pins. For the right rear that’s C135 pins 43 and 42 to sensor pins 1 and 2. For the left rear it’s C135 pins 36 and 37 to sensor pins 1 and 2. If the voltages are greater than 9 volts, install a new wheel speed sensor. If not, Ford directs you to install a new ABS module.
Step F2 is the most useful step for anyone with a scan tool that shows live data. It shows whether one wheel disagrees with the other three, and it also catches the cheap cause that Ford lists first, mismatched tire sizes. A wrong size tire on one corner makes that wheel turn at a different speed, and the module can read that as a bad signal. Check that all four tires are the same size before buying parts.
The rear sensor ring is part of the halfshaft
Heads up, because this one stings a little. One detail in the Ford procedure changes the cost picture if step F4 finds a damaged ring. In the rear wheel speed sensor removal table, Ford’s note for the sensor ring says the ring isn’t serviceable and must be replaced as part of the rear halfshaft assembly. In other words, there’s no separate tone ring listed in the procedure. If the teeth are cracked or missing, the fix is a halfshaft, not a ring.
That’s another reason to follow the test order. A sensor is a small part. A halfshaft is a much bigger job. Inspect the ring carefully under a good light while you’ve the sensor out, rotating the wheel through a full turn, and only move on to a halfshaft if the teeth are actually damaged.
Rear wheel speed sensor replacement, per the Ford manual
Good news: once you’ve proven the sensor’s bad, the actual swap is easy. The Ford procedure for the 2004 LS rear wheel speed sensor and sensor ring is short. It’s listed under the Brakes and Traction Control section of the manual as Rear Wheel Speed Sensor and Sensor Ring. Ford’s location view for the rear sensor is View 151-50 in the component locator. Here’s the procedure as the manual gives it, with the removal order from the illustration.
Before you start
Ford’s note: clean off any dirt and foreign material from around the rear anti-lock brake sensor before removing it. That keeps grit out of the sensor bore when the old sensor comes out.
- With the vehicle in NEUTRAL, position it on a hoist.
- Remove the parts in the order shown in the Ford illustration: item 1, the connector; item 2, the bolt; item 3, the wheel speed sensor; item 4, the wheel speed sensor harness.
- For item 4, Ford’s removal note says to remove the rear anti-lock brake sensor harness from the upper control arm clip.
- Item 5 in the illustration is the sensor ring. As covered above, Ford notes it isn’t serviceable and is replaced as part of the rear halfshaft assembly.
- To install, reverse the removal procedure. Tighten the sensor bolt to 9 Nm (80 lb-in).
| Fastener | Ford specification |
|---|---|
| Rear wheel speed sensor bolt | 9 Nm (80 lb-in) |
A few practical points follow straight from that procedure. Because the harness clips to the upper control arm, route the new harness through the same clip so it can’t rub on suspension parts or the halfshaft as the suspension moves. Look at the Ford illustration before you pull anything, since the connector and the clip are easier to deal with once you know where they are. And note that 80 lb-in is a light torque. Use an inch pound torque wrench rather than a large ratchet, because it’s easy to strip or crack a small fastener at that value.
After installation, clear the codes with the scan tool and repeat the self test, as every branch of the Ford pinpoint tests directs. Then drive the car and recheck for continuous codes. If the ABS lamp stays off and the wheel speed PIDs agree, the repair is done.
Ford part numbers and what to know before ordering
Before you click buy, read this section. The Ford parts catalog on FordPartsGiant lists the rear wheel speed sensors for the Lincoln LS by side. Both numbers below have been superseded from earlier numbers, and FordPartsGiant lists both as discontinued, so dealer availability may be limited.
| Position | Current Ford number | Replaces | Status on FordPartsGiant |
|---|---|---|---|
| Driver side rear (LH) | 3W4Z-2C190-AA | XW4Z-2C190-BA | Discontinued |
| Passenger side rear (RH) | 3W4Z-2C190-BA | XW4Z-2C190-AA | Discontinued |
Notice the crossed suffixes. The current driver side number ends in AA and replaces an older BA number, while the current passenger side number ends in BA and replaces an older AA number. If you’re matching an old sensor in hand to a listing, check the full number and the side, not just the last two letters.
Because both Ford numbers are discontinued, many owners will end up shopping aftermarket sensors. We aren’t listing aftermarket cross references or prices here, because we could not verify them against a manufacturer catalog for this article. When you shop, confirm the listing names the correct side and fits the LS year you own, and compare the connector shape to the one on your car before you install it. My advice: skip the cheapest no-name sensor and buy from a brand that stands behind it.
Which cars share this setup
If you’ve got a Thunderbird in the garage, listen up. According to the FordPartsGiant listings for these two Ford numbers, the same rear sensors are listed for the 2000 to 2006 Lincoln LS and the 2002-2005 Ford Thunderbird with the 3.9 liter V8. The torque value and procedure in this article come from the 2004 LS V8 manual, so if you own one of the other cars, confirm the steps against the manual for your exact model and year.
The front sensors on these cars have their own history. Ford Technical Service Bulletin 04-22-13 covers Lincoln LS and Thunderbird cars equipped with a bolt on front wheel speed sensor that may show the ABS and traction control or AdvanceTrac lamps with C1145 or C1155 stored. That bulletin calls for replacing the front sensor with a coat of Motorcraft XG-3-A silicone dielectric compound on the O-ring and sensor body, and venting the front bearing cap by drilling two small holes. Ford notes the updated front sensor can be identified by blue tape on the cable. That bulletin is for the front sensors, not the rear, so it isn’t a fix for C1165, C1175, C1235, or C1236. It’s useful context if your scan tool shows a front code instead.
Common mistakes that waste time and money
- Reading the wrong module. A generic engine code reader won’t show ABS codes. Without the actual code, you’re guessing at four sensors.
- Mixing up sides. Ford’s LR and RR are driver side and passenger side on a US car, and the current part numbers have crossed suffixes. Check both before ordering.
- Ohms testing an active sensor and calling it good. Ford’s tests check wiring, shorts, and supply voltage. A resistance reading across the sensor alone doesn’t prove an active sensor works.
- Skipping the tire check. Ford lists mismatched tire sizes as a cause of missing signal codes. A replaced tire of a different size on one corner can set a code.
- Ignoring the wire. Ford’s caution in Test F is to inspect the sensor wire with a good light. A chafed harness near the upper control arm clip can act just like a bad sensor.
- Overtightening the bolt. The specification is 9 Nm (80 lb-in). That’s a small value, and it’s easy to exceed with a full size ratchet.
For more brake and electrical guides across makes, our car maintenance hub collects them in one place. If you are chasing a different lamp that will not shut off, our article on a brake light switch problem on the Nissan Maxima shows another example of a small part creating a warning that looks like a bigger fault.
Make the diagnosis reproducible before authorizing an ABS module
I would save the scan report before clearing anything: the exact code, which module stored it, whether it is current or continuous, and what the car was doing when the lamps appeared. A report that just says “ABS sensor” leaves out the very distinction between a circuit fault and a missing wheel signal that determines which Ford test to use.
The original charts are available in Ford Pinpoint Test E and Pinpoint Test F. Open the illustrations as well as the text. Connector views, which side of a disconnected connector is being measured, ignition state and the preceding disconnections belong to the test. A number copied without those conditions is not an equivalent measurement.
For each step, write down the measured result and the next branch taken. Keep resistance measurements confined to the isolated circuits and conditions in the chart; do not measure resistance on an energized circuit. If a diagram, connector orientation or terminal identification is unclear, stop before probing. Ford’s warning about proper terminal adapters is there to prevent the diagnostic process from creating a loose connection.
For a road-data comparison, use a safely secured logging tool or a second qualified person; the driver must not watch four changing numbers instead of the road. Do not deliberately provoke wheel lock or traction-control intervention to see whether the repair worked. Abnormal pedal feel, a fluid leak or another braking warning needs assessment before a road test.
On the estimate, separate diagnostic labor, a proven sensor or wiring repair, and any additional work supported by the test results. Ask for the failed measurement if a module is recommended. I am happy to pay for a proper diagnosis; I am much less happy paying for a succession of parts that happen to sit in the same diagram.
Keep the final record with the original report: repaired circuit or replaced component, repeat self-test outcome, and post-repair code and wheel-speed check. That gives the next technician a useful starting point if an intermittent fault returns rather than the unhelpful note “light reset.”
FAQ
Can I drive a Lincoln LS with the ABS and traction control lights on?
Normal braking still works, but the anti-lock and traction control functions are disabled while the ABS lamp is on. The wheels can lock in a hard stop on a slippery surface. Get the code read and the repair done soon.
What does code C1165 or C1175 mean on a Lincoln LS?
In the Ford DTC index, C1165 is Wheel Speed Sensor RR Input Circuit Failure and C1175 is Wheel Speed Sensor LR Input Circuit Failure. Ford sends both to Pinpoint Test E, which checks the circuit for shorts and opens before pointing to the sensor or the ABS module.
What do C1235 and C1236 mean?
C1235 is Wheel Speed RR Input Signal Missing and C1236 is Wheel Speed LR Input Signal Missing. Ford sends both to Pinpoint Test F, which starts with comparing the four wheel speed PIDs while driving.
Where is the rear wheel speed sensor on a 2004 Lincoln LS?
It mounts at the rear knuckle near the halfshaft, held by one bolt, and reads a sensor ring on the rear halfshaft. The harness runs to a clip on the upper control arm. Ford’s component locator shows it in View 151-50.
What is the torque for the Lincoln LS rear wheel speed sensor bolt?
The Ford manual specifies 9 Nm (80 lb-in).
Can the rear tone ring be replaced by itself?
Not according to the Ford procedure. The manual says the rear sensor ring isn’t serviceable and must be replaced as part of the rear halfshaft assembly.
Sources: Ford 2004 Lincoln LS V8 workshop manual sections for the Rear Wheel Speed Sensor and Sensor Ring, ABS Control Module DTC Index, Pinpoint Tests E and F, and torque specifications (via charm.li); Ford TSB 04-22-13; FordPartsGiant listings for 3W4Z-2C190-AA and 3W4Z-2C190-BA.
Note To Reader: Car Nut Chronicles is reader supported. We may post content which contains links to affiliate sites such as Amazon where we may earn a small commission. This helps us keep the lights on and the articles you enjoy being produced. Thank you for your readership, we appreciate you!

2004 Lincoln LS ABS and Traction Light: Rear Wheel Speed Sensor Fix
Fix the ABS and traction lights on a 2004 Lincoln LS: read codes C1165, C1175, C1235 or C1236, run the…
Alpine A110 R: The Best Looking Car of the Last Five Years
The Alpine A110 R is a carbon wheeled, 1,082 kg French spaceship with a 300 PS turbo four, a 177…
How to Keep Mice Out of a Car Engine in Storage: What Actually Works
Keep mice out of a stored car engine: remove food, seal quarter inch gaps and set snap traps. What research…
1970s Muscle Car Paint Restoration: Prep Thin Panels and Get the Color Right
How to repaint a 1970s muscle car: fix rust first, respect thin metal, and shoot a period color without inventing a paint code or warping the panels.
Top 10 Fastest Pontiacs: A Hidden Need For Speed
Speed Legends: Pontiac’s Top 10 Fastest Models That Define Performance Excellence Although Pontiac is no longer in production, its legacy lives on among speed enthusiasts, so we’re counting down the top 10 fastest Pontiacs produced! We’ve compiled data from J.D. Power, along with insights from muscle car experts at Hagerty…
When Front-Wheel-Drive Burnouts Were Cool: 66 Olds Toronado
Chain-Driven Front Wheel Drive Left an Indelible Impression and Cemented the 66 Olds Toronado Into Muscle Car Memory The inaugural Oldsmobile “Olds” Toronado, a front-wheel-drive powerhouse launched in ’66, defied convention with its robust chain mechanism, a two-inch-thick assembly linked to a 180-degree-turned three-speed Turbo-Hydramatic transmission. This engineering marvel, splashed-lubricated…
Biden’s New NHTSA Policy Now Stops You From Fixing Your Own Car
When a vehicle experiences problems, the onboard diagnostics system (OBD) is the gateway for vehicle owners and independent mechanics to diagnose and fix these issues, but due to a new NHTSA policy that may change. One state has is now recognizing the importance of this access. Massachusetts has officially enacted…
The Lamborghini Urus Is Really, Really Good. Guaranteed.
With this Latest Iteration, Lamborghini hits a Homerun: The Urus The Lamborghini Urus is a true masterpiece in the world of automotive engineering. It is a vehicle that combines the style and sophistication of a Lamborghini with the practicality and versatility of an SUV. This car is truly one of…
Spider Silk Supercar Is A Thrilling Challenge
Revolutionary Supercar Crafted from Spider Silk Promises Unprecedented Strength and Lightness A groundbreaking endeavor in the automotive world is underway as a US company Velozzi explores the possibility of creating a spider silk Supercar. A material proven to be five times stronger than steel when thousands of nano strands form…

